Security Light Installation Goldsboro NC You Can Count On
Licensed electricians for motion sensors, floodlights, and dusk-to-dawn fixtures
Security Light Installation Goldsboro NC means more than a bright bulb on a pole. We mount motion sensors, floodlights, and photocell fixtures so your driveway, back door, and side yard stay lit when someone walks up. If you have been searching for a security lighting install Goldsboro NC crew that knows Wayne County homes, we wire it clean, test every trigger, and leave the switch labeled.
Security Light Installation Goldsboro NC Explained
Security Light Installation Goldsboro NC is the electrical work that adds exterior fixtures, motion sensors, and photocell controls to a home or small business so the property is lit when it matters. A proper job starts at the circuit, not the fixture. We check whether the panel has room for a new breaker, run Romex wire or THHN wire through conduit where it is exposed, mount a junction box, and bond the fixture to the grounding system. Done right, the light comes on only when it should and the circuit does not nuisance-trip.
Most calls we get in Goldsboro come from one of three situations. A homeowner wants the dark side yard covered after a break-in on the block. A landlord needs new security light installation Goldsboro at a rental near Downtown Goldsboro or Lincoln Homes. Or a business owner wants a security light installation in Goldsboro North Carolina that survives hurricane-season wind and rain. If you are typing security light installation near me Goldsboro NC into your phone at 9 p.m. because the porch light quit, we can usually schedule you the next morning.
Why Goldsboro Homeowners Add Security Lighting
Exterior lighting is one of the cheapest electrical upgrades you can make, and it changes how the property feels after dark. Here is what a clean install actually gets you.
Deterrence That Works
A motion light that snaps on at 30 feet does more than a porch bulb left burning all night. We aim sensors across driveways and side gates so a person crossing the beam triggers the fixture before they reach a door. Most customers see fewer late-night loitering complaints within the first month.
Fewer Tripped Breakers
Old exterior circuits often share a 15-amp breaker with garage outlets and a freezer. We run a dedicated 20-amp circuit for new security lighting install Goldsboro NC work, which stops the tripping circuit breaker you have been resetting every storm. That one change alone fixes most flickering lights on the same run.
Lower Power Bills
LED floodlights draw 15 to 30 watts instead of the 150 watts an old halogen pulls. A dusk-to-dawn photocell keeps them off during daylight, so a two-fixture setup can cut exterior lighting cost by 70 percent or more. We size the transformer and breaker to match.
Code-Correct Wiring
Every outdoor fixture we install is UL Listed and wired to NEC standards, with GFCI protection where the circuit serves receptacles as well. We use weather-rated junction boxes and seal conduit penetrations so water never follows the wire into your wall. That is what keeps an inspection clean.
How Our Security Light Installation Process Works
You should know exactly what happens from the first phone call to the final walk-around. Here is the five-step path we follow on every Goldsboro job.
Phone Walkthrough
We ask what you want lit, where the panel sits, and whether the area has power already. Five minutes on the phone usually tells us if this is a single-fixture job or a multi-circuit layout. You get a rough range before we ever roll a truck.
On-Site Assessment
A licensed electrician walks the property, checks panel capacity with a clamp meter, and looks for existing conduit or an unused circuit. We mark fixture heights and sensor angles with you standing there, because the best coverage point is not always the obvious one.
Circuit and Rough-In
We kill power at the breaker, install a new breaker if needed, and pull Romex wire or THHN through conduit to each fixture location. Junction boxes get mounted and grounded. This stage takes two to four hours on a typical two-light job.
Fixture Mounting
Floodlights, motion sensors, and photocells go up on the marked points. We seal every penetration, aim each sensor, and set the sensitivity so a passing car does not trigger the light. You watch the first test from the driveway.
Test and Label
We trip the breaker on purpose, confirm the GFCI holds, and walk the coverage zone after dark if you want. Every new breaker gets labeled at the panel. Before we leave, you know which switch controls what and how to adjust the sensor.
Local Electrical Expertise You Can Verify
Our electricians hold North Carolina Electrical Contractor License credentials and work to NEC and NFPA 70E standards on every job. We have wired exterior lighting on brick bungalows near Herman Park, vinyl-sided ranches out toward Woodford, and metal shops along the US 70 corridor. That range matters, because a 1940s Goldsboro home with cloth-wrapped wiring needs a different approach than a 2015 build with Romex already in the wall. We carry the tools to handle both on the same truck.
- State-licensed electrical contractor working under North Carolina Electrical Contractor License rules
- Every install inspected against NEC and NFPA 70E before we sign off
- Experienced with cloth wiring, aluminum branch circuits, and modern Romex alike
- Trained on Square D, Eaton, and Siemens panels common in Wayne County homes
- Equipped with Fluke meters and Klein Tools for live-circuit diagnostics
Why Goldsboro Picks Us for Security Light Installation Goldsboro NC
Plenty of handymen will hang a floodlight. We do the electrical work behind it, which is the part that keeps the light on and your panel happy.
Dedicated Circuits, Not Splices
We run a new circuit from the panel instead of tapping the nearest outlet. That means no overloaded circuit, no shared neutral problems, and no mystery breaker trips six months later. On a two-fixture job we typically pull 40 to 60 feet of new wire.
Same-Day Service Available
Call before noon and we can often complete same-day security light installation Goldsboro jobs that only need one circuit and one or two fixtures. Larger layouts get scheduled within 48 hours. You get a call when the truck is 30 minutes out.
We Test After Dark
Sensor aim is everything, and you cannot judge it at 2 p.m. On request we come back after sunset or set the fixture to manual for your evening test. If the beam misses the gate, we adjust it. That is part of the security lighting install Goldsboro NC service, not an extra trip.
Clean Work, Labeled Panel
Conduit runs straight, penetrations are sealed, and every new breaker is labeled in plain text. If you ever sell the house, the next electrician can read your panel in ten seconds. We also leave the sensor adjustment instructions taped inside the panel door.
What Our Security Light Installation Covers
Every job is different, but a standard security light installation includes the circuit work, the fixture mounting, and the testing that makes it reliable. Here is what we handle on a typical Goldsboro visit.
What's Included
Circuit and Breaker Work
We verify panel capacity with a clamp meter, install a correctly sized breaker, and pull new Romex wire or THHN in conduit to each fixture location. If your panel is full, we tell you before we start.
Fixture Mounting and Sealing
Floodlights, motion sensors, and photocells get mounted on solid backing, grounded, and sealed at every penetration. We use weather-rated junction boxes so water cannot track the wire into your wall.
Sensor Aim and Calibration
Detection zones get aimed at the driveway, gate, or side yard you actually care about. We set sensitivity so pets and passing cars do not trigger the light, then test the range with you standing in the beam.
GFCI Protection Where Required
If the exterior circuit also serves receptacles, NEC requires GFCI protection. We install a GFCI receptacle or breaker so the whole run is protected and the light circuit does not nuisance-trip.
Panel Labeling and Walkthrough
Every new breaker gets labeled in plain text. We walk you through the switch, the sensor override, and how to adjust sensitivity. You leave knowing exactly how your system works.
Problems We Solve With Better Exterior Lighting
Dark corners, tripping breakers, and dead exterior outlets are the three most common complaints we hear. All three trace back to the circuit, not just the fixture.
Side yard and driveway stay pitch black after sunset
Dark approaches give intruders cover and make it hard to see steps, pets, or a delivery driver at the door. Most break-ins on residential blocks happen at the unlit side of the house.
We map the coverage zone with you, then mount motion floodlights at the right height and angle. Two well-aimed fixtures usually cover a full driveway and side gate. We test the detection range before we leave.
Exterior breaker trips every time the lights come on
A tripping circuit breaker means the exterior run is overloaded or undersized. Reset it enough times and the breaker itself weakens, which can leave the whole circuit dead.
We measure the actual load with a clamp meter, then run a dedicated 20-amp circuit for the security lights. That removes the shared load and stops the nuisance trips. If the breaker is worn, we replace it with a correctly rated unit.
Old exterior outlet is dead and lights will not power on
A failed GFCI receptacle kills everything downstream, including the security light tied to that circuit. Homeowners often assume the fixture is bad when the outlet is the real problem.
We test the outlet with a GFCI tester, replace the failed receptacle, and confirm power reaches the fixture. If the wiring behind it is corroded, we replace that section with fresh wire and re-seal the box.
Existing lights flicker or buzz when the sensor triggers
Flickering usually points to a loose wiring connection or a failing sensor head. Left alone, a loose splice heats up and can arc inside the box.
We open the fixture, inspect the splices, and re-terminate with fresh wire nuts. If the sensor head is failing, we swap it for a UL Listed replacement and re-aim the detection zone.
When Goldsboro Homeowners Call Us
A homeowner near Herman Park wants the back alley lit after a neighbor's break-in.
We install two motion floodlights on a dedicated circuit, aim one at the alley gate and one at the back door, and set sensitivity so the neighbor's cat does not trigger them.
The alley is covered from the fence line to the door, and the homeowner can see who is back there before opening up.
A landlord with a duplex in Lincoln Homes needs exterior lighting that tenants cannot leave on all day.
We add a dusk-to-dawn photocell fixture over the shared entry and a motion light on the side yard, both on one new 20-amp circuit with a labeled breaker.
The entry stays lit from dusk to dawn automatically, and the landlord stops paying for lights left on around the clock.
A small shop on the West End loses tools off the back lot at night.
We mount two LED wall packs on the building, run conduit along the block wall, and add a photocell so the lights run only after dark. A GFCI receptacle on the same run powers a camera.
The back lot is fully lit, the camera has power, and the shop has not lost a tool since the install.
A homeowner in Woodford wants coverage without running new wire across a long driveway.
We use the existing exterior circuit where it is safe, upgrade the breaker, and install a solar-assist motion fixture at the far end of the drive to avoid a 120-foot conduit run.
The driveway is covered end to end without trenching, and the customer saves the cost of a long wire pull.
Tools and Methods We Use
Tools & Equipment
Fluke clamp meter
Measures actual load on the exterior circuit before we add fixtures, so we size the breaker correctly instead of guessing.
Klein Tools voltage tester
Confirms power is dead at the fixture box before we touch a wire, and verifies the new circuit is live after the breaker goes back on.
GFCI tester
Checks exterior receptacles on the lighting circuit to confirm protection is working and the outlet is not the reason the lights are dead.
Southwire Romex wire
Standard 12-gauge and 14-gauge branch wiring for interior-to-exterior runs where the cable stays inside the building envelope.
THHN wire and conduit
Used for exposed exterior runs, garage walls, and anywhere the wire needs mechanical protection from weather or impact.
Leviton and Hubbell fixtures
UL Listed motion sensors, photocells, and floodlight heads that hold up to Goldsboro humidity and summer heat.
Methods
NEC-compliant circuit design
We size the breaker, conductor, and GFCI protection to NEC requirements for outdoor lighting. That means no undersized wire, no missing ground, and no failed inspection when the county checks the work.
Dedicated circuit strategy
Security lighting gets its own breaker whenever the panel allows. A dedicated circuit stops the lights from sharing load with garage outlets or a freezer, which is the root cause of most tripping breaker complaints.
Coverage mapping
Before mounting anything, we walk the property and mark where the detection zones should overlap. Two correctly aimed fixtures beat four random ones, and the overlap closes the gaps a single sensor leaves.
After-dark verification
Sensor aim cannot be judged in daylight. We set the fixture to manual or return after sunset to confirm the beam lands where you need it, then adjust sensitivity to filter out pets and passing cars.
How Security Lighting Works in Goldsboro
Goldsboro sits in Wayne County, where summer humidity runs high and hurricane-season storms push rain sideways into every exterior fixture. That climate punishes cheap hardware. We spec UL Listed wet-rated fixtures and seal every conduit penetration, because water following a wire into a wall is the number one cause of exterior circuit failure we see. Building stock matters too. Homes near the Historic District and Downtown Goldsboro often still have cloth-wrapped wiring and 100-amp panels, so adding a new circuit means checking panel capacity first. Newer builds out toward Spring Creek and Woodford usually have Romex in the walls and room at the panel, which makes a security lighting install near me Goldsboro NC job faster. Either way, we pull a Wayne County permit when the work adds a circuit, and we meet the inspector on site.
Service Areas
Older homes with cloth wiring and smaller panels. We check capacity before adding an exterior circuit, and often recommend a panel upgrade first.
A mix of 1960s ranches and newer builds. Many homes here have an existing exterior outlet we can reuse for a faster install.
Small commercial lots with back-alley access. Wall packs and photocells work better here than residential floodlights.
Longer driveways and rural lots. Voltage drop matters, so we plan wire gauge and conduit runs carefully before quoting.
Local Considerations
Hurricane-season wind and driving rain
Exterior fixtures take direct weather. We use wet-rated UL Listed hardware and seal every penetration so water cannot reach the box or the wire inside the wall.
High summer humidity
Humidity corrodes cheap terminals and sensor heads. We use corrosion-resistant connectors and Hubbell or Leviton fixtures rated for damp locations.
Older panels with limited breaker space
Many Goldsboro homes run 100-amp panels with no open slots. We test capacity first and discuss a panel upgrade if the security circuit will not fit safely.
Clay and sandy soil in Wayne County
Ground movement shifts exterior conduit and can crack fittings over time. We use expansion-friendly fittings and support runs so the conduit stays sealed.
Dark Side Yard to Full Coverage
A Ridgewood homeowner had one porch bulb covering a 40-foot side yard. The gate and back fence line were completely dark, and a neighbor had been broken into two houses down.
We ran a dedicated 20-amp circuit, mounted two LED motion floodlights, and aimed them to overlap across the gate and fence line. Detection range now covers the full 40 feet, and the breaker has not tripped once in six months.
Maintenance & Follow-up
Wipe the sensor lens twice a year and test the trigger monthly by walking the zone. Replace the LED heads when output drops noticeably, usually after 8 to 10 years of nightly use.
A Downtown Goldsboro duplex shared one 15-amp breaker between a freezer, garage outlets, and two exterior lights. The breaker tripped every storm, leaving the entry dark for tenants.
We installed a new 20-amp dedicated breaker for the exterior lighting, replaced a failed GFCI outlet on the run, and added a dusk-to-dawn photocell over the shared entry. No trips in the four months since.
Maintenance & Follow-up
Press the GFCI test button monthly and reset it. Keep the photocell lens clear of cobwebs, and label any future breaker additions so the panel stays readable.
A West End shop owner had two wall packs that stopped working after a storm. The exterior outlet feeding them was dead, and the wiring behind it showed corrosion from years of rain intrusion.
We replaced the corroded wire section with fresh THHN in sealed conduit, installed a new GFCI receptacle, and re-mounted both wall packs on a photocell. The back lot is lit from dusk to dawn and the camera on the same run has power.
Maintenance & Follow-up
Check the conduit seals each spring before storm season and test the GFCI monthly. If a wall pack flickers, call us before the connection heats up further.
What Security Light Installation Costs
Typical 2026 pricing in the Goldsboro area runs $280 to $850 for a residential security lighting install, and $900 to $2,400 for commercial wall-pack layouts. The range depends on fixture count, whether a new circuit is needed, and how far we have to pull wire. We quote a flat range before we start, and the number does not move unless you add scope. If you want an affordable security light installation in Goldsboro North Carolina, a single motion floodlight on an existing circuit is the cheapest path and still delivers real coverage.
Pricing Factors
Fixture count
Each additional floodlight or wall pack adds hardware cost and mounting time. Two fixtures cover most residential driveways; three or four are common on corner lots and commercial properties.
New circuit vs. existing
Tapping an existing exterior circuit is the cheapest option. Running a dedicated 20-amp breaker and new wire adds material and labor but eliminates tripping breaker problems down the road.
Conduit and wire distance
Exposed runs need conduit, and long pulls need heavier wire to avoid voltage drop. A 100-foot run costs noticeably more than a 20-foot run from the panel to the fixture.
Panel capacity
If your panel has no open breaker slots, we may need to install a subpanel or upgrade the main panel. That is a separate line item and we tell you before any work begins.
Fixture grade
Basic LED floodlights sit at the low end. Commercial wall packs, photocells, and smart motion sensors with adjustable sensitivity push the price up but last longer in Goldsboro weather.
Permit and inspection
Adding a circuit triggers a Wayne County electrical permit. The fee is modest, and we handle the paperwork and meet the inspector so you do not have to schedule anything.
Investment Range
$280 - $2,400 depending on scope
Based on project scope
Value You Get
Exterior lighting is one of the few electrical upgrades that pays back in both safety and energy savings. LED fixtures cut power draw by 70 percent or more versus old halogen, and a correctly wired circuit stops the breaker trips that lead to bigger repairs later.
How much does security light installation cost in Goldsboro NC?
Most residential jobs run $280 to $850 in 2026, depending on fixture count and whether a new circuit is needed. A single motion floodlight on an existing circuit sits at the low end. Two fixtures with a dedicated 20-amp breaker, conduit, and a photocell push toward the top. Panel work or long conduit runs add cost.
What type of security lights are best for Goldsboro North Carolina?
LED motion floodlights rated for wet locations handle Goldsboro humidity and hurricane-season rain best. Look for 3,000 to 5,000 Kelvin output and a 110-degree detection angle. Dusk-to-dawn photocells work well for driveway poles. We avoid halogen fixtures because they burn hot, pull 150 watts, and fail faster in our summer heat.
Who installs security lights near me in Goldsboro NC?
Goldsboro Electric Pros installs exterior security lighting across Wayne County, including Downtown Goldsboro, Ridgewood, and Westhaven. We handle the circuit, the fixture, and the sensor calibration. Call (919) 850-5629 and we can usually give you a range over the phone before scheduling a visit.
Do security lights need a permit in Goldsboro?
A like-for-like fixture swap on an existing circuit usually does not require a permit. Adding a new circuit, running new conduit, or installing a subpanel does trigger a Wayne County electrical permit and inspection. We pull the permit when it applies and meet the inspector on site so you do not have to.
Licensed, Insured, and Local
Certifications
Reviews
Ran a new circuit for two motion lights on our side yard in Ridgewood. Breaker labeled, sensor aimed perfectly, and they came back after dark to check coverage. No more tripping breaker and the yard is finally lit.
Needed security lighting install Goldsboro NC work at a rental near Downtown. They replaced a dead GFCI outlet and added a dusk-to-dawn fixture. Tenants stopped complaining about the dark entry. Fair price, showed up on time.
Wall packs on our shop back lot were flickering for months. They traced it to corroded wiring, replaced the section, and sealed the conduit. Back lot is fully lit and the camera on the same circuit works again.
Quoted a range over the phone and the final bill matched. Installed a photocell and two LED floods on a dedicated breaker. Clean conduit work, no mess, and they explained how to adjust the sensor sensitivity.
Other Electrical Work We Handle
Electrical Panel Repair
If your panel is full or a breaker will not reset, new security lighting has nowhere to land. We repair the panel first, then run the exterior circuit so the whole system stays balanced.
Electrical Panel RepairElectrical Panel Replacement
Older Goldsboro fuse boxes and 100-amp panels often cannot carry a new exterior circuit. We upgrade to a 200-amp Square D or Eaton panel, which gives security lighting its own breaker and room to grow.
Electrical Panel ReplacementCircuit Breaker Replacement
A breaker that trips every time the floodlight kicks on is a sign of a weak or undersized breaker. We swap it for a correctly rated unit and confirm the new security light circuit holds under load.
Circuit Breaker ReplacementFuse Box Repair
Homes near the Historic District still run fuse boxes. Before adding exterior lighting we repair or replace blown fuse holders so the new circuit is not sharing a 15-amp fuse with half the house.
Fuse Box RepairElectrical Short Circuit Repair
Water intrusion at an old exterior box can short the whole lighting run. We trace the fault with a multimeter, repair the damaged section, and re-seal the fixture before finishing the security light install.
Electrical Short Circuit RepairPower Outage Repair
If half your exterior lights died at once, the problem is upstream at the panel or meter. We diagnose the outage, restore power, and confirm the security lighting circuit is back on its own breaker.
Power Outage RepairElectrical Wiring Repair
Rodent-chewed or sun-cracked exterior wire fails fast in North Carolina heat. We replace damaged runs with fresh Romex or THHN in conduit so your security lights stay reliable through storm season.
Electrical Wiring RepairElectrical Wiring Installation
New exterior circuits start here. We pull dedicated wire from the panel to each fixture location, size the conductor to the load, and leave enough slack for future additions.
Electrical Wiring InstallationWhole Home Rewiring
If your Goldsboro home still has cloth or aluminum branch wiring, exterior lighting is a small part of a bigger fix. We rewire the house and add the security circuit in the same project.
Whole Home RewiringOutlet Repair
Exterior GFCI outlets often feed landscape and security lighting. When one dies, the lights go with it. We repair the outlet and restore power to the whole exterior run.
Outlet RepairOutlet Installation
Adding a weather-rated outlet near the driveway gives you a place to plug in temporary lighting or a portable generator. We install it on the same circuit plan as your security lights.
Outlet InstallationGFCI Outlet Installation
NEC requires GFCI protection on outdoor receptacles. We install GFCI receptacles that protect both the outlet and any lighting tied to that exterior circuit.
GFCI Outlet InstallationAFCI Outlet Installation
AFCI breakers catch the arcing faults that start attic and wall fires. We install AFCI protection on interior circuits that share a panel with your new security lighting.
AFCI Outlet InstallationSwitch Repair
A sticky exterior switch can leave your security lights on all day or off all night. We repair or replace the switch and confirm the sensor override still works.
Switch RepairDimmer Switch Installation
Dimmers on porch and patio fixtures let you dial down brightness when full flood output is too much. We install dimmers rated for LED loads so the fixture does not buzz.
Dimmer Switch InstallationLight Fixture Repair
Sometimes the fixture is fine and the wiring behind it is not. We diagnose the connection, repair the box or splice, and get the existing exterior light working again.
Light Fixture RepairLight Fixture Installation
Beyond security lights, we hang porch lights, garage fixtures, and shop lights. Same circuit discipline applies, so a new fixture never overloads an existing run.
Light Fixture InstallationCeiling Fan Installation
Ceiling fan boxes need proper bracing, and we install them to code. If your panel is getting a new circuit for security lighting, we can add a fan circuit in the same visit.
Ceiling Fan InstallationCeiling Fan Repair
A wobbly ceiling fan often points to a loose box or a wiring connection that is failing. We tighten, re-splice, and test so the fan stops shaking and the circuit stays stable.
Ceiling Fan RepairRecessed Lighting Installation
Recessed cans under a carport or porch overhang pair well with motion lights. We install them on a switched circuit so you control them separately from the security fixtures.
Recessed Lighting InstallationMotion Sensor Light Installation
This is the core of most security lighting jobs. We mount the sensor head at the right height, aim the detection zone, and set sensitivity so pets and passing cars do not trigger it.
Motion Sensor Light InstallationExterior Lighting Installation
From soffit lights to wall packs, exterior fixtures take a beating from Goldsboro weather. We install UL Listed wet-rated fixtures and seal every penetration against rain.
Exterior Lighting InstallationLandscape Lighting Installation
Low-voltage path and garden lights often share a transformer with security fixtures. We balance the load so adding landscape lighting does not dim the security lights.
Landscape Lighting InstallationGenerator Installation
A standby generator keeps security lights on during a storm outage. We install the transfer switch and confirm the exterior lighting circuit is on the backed-up panel.
Generator InstallationGenerator Repair
If your generator will not start, your security lights go dark in the next outage. We repair the unit, test the transfer switch, and verify the lighting circuit transfers cleanly.
Generator RepairStandby Generator Service
Annual service keeps a standby generator ready for hurricane season. We change oil, test the battery, and confirm your security lighting circuit is included in the backup load.
Standby Generator ServicePortable Generator Hookup
A proper inlet box and interlock let you run exterior lights from a portable generator. We install the hookup and label which breakers you can safely energize.
Portable Generator HookupWhat Goldsboro Customers Say
Real experiences from customers who chose our Security Light Installation services
"We had two break-ins on our street last spring, so I wanted real coverage on the side yard. The crew ran a dedicated circuit from the panel, mounted two motion floods, and aimed them so the gate is covered. First night a raccoon set it off and I knew it worked. Clean work, labeled breaker, no mess left behind."
Marcus T.
Homeowner, Ridgewood
"I manage four rentals and needed security lighting install Goldsboro NC work done fast at a duplex near Downtown. They came out the next morning, replaced a dead exterior outlet, and added a dusk-to-dawn fixture over the shared entry. Tenants stopped calling me about the dark stairwell. Price matched the quote exactly."
Denise W.
Landlord, Downtown Goldsboro
"My back lot was pitch black and I was losing tools off the truck. Goldsboro Electric Pros added a 20-amp circuit, two LED wall packs, and a photocell so they run only at night. The old breaker used to trip every storm; that stopped completely. They came back after dark to check the coverage with me."
Ray P.
Shop Owner, West End
Get Your Security Light Installation Goldsboro NC Quote
Call (919) 850-5629 and tell us what you want lit. We will give you a straight range, schedule a visit, and have your exterior covered before the next dark evening. Licensed, insured, and local to Wayne County.